1410 furnace
Yard Sale
How to Order
Thermolyne FB1410M Furnace
Price: $450.00
Used FB1410M muffle heat treating furnace. Dimensions interior 6″ x 5″ x 4.5″. Dimensions exterior 15.8″ x 10″ x 14.5″ 230 VAC 60 hertz single phase. Operating temperature is 212 F to 1,800 F however I would limit the temp to 1,600 degrees F. The furnace would be fine for annealing brass cases or heat treating steels that have a lower hardening temp. The heating elements come as a flat ceramic sheet with the elements embedded in the sheet. The sheet is folded at the indicated places. The old elements come out the rear of the furnace, the new one is slipped in, and connected to the wiring. Much easier than fooling around with a loose coil of high temp wire. Operators manual included.
I would still be using this furnace but needed one that can operate at higher temps and no longer need this one. Photo is of a new unit.
Reloading Dies 43 Mauser
43 Mauser dies
Price: $30.00
43 Mauser reloading die set. Two die set. Lee Precision. Includes an RCBS style shellholder. Load your own ammo for the M-71 and M-71-48 Mausers and some Remington Rolling Block rifles. Good condition, never used.
Lee 50 BMG Loading Dies
Price: $85.00
Lee Precision two die set to reload the 50 BMG cartridge. Includes a sizer die (BMG-B) and a bullet seating die (50 BMG-G1). Also included is a 50 BMG shellholder for the Lee Classic press. These are lightly used to test the Walnut Hill-50 press when loading 50 BMG ammo. The dies are in good condition, like new, and no longer needed.
Lee 25 ACP Loading Dies
Price: $40.00
Lee Precision three die set to reload the 25 ACP cartridge. The set is used but is in like new condition. It was used to test how different bullet shapes and lengths would feed and function in the little 25 ACP pistols. That work is done and the set is no longer needed.
Bits & Pieces
Price: $12.00
Collection of bits and pieces including an M1 Garand cleaning rod with two swivel handles that also serve as a disassembly tool. New, unused chamber brush-30-06. 30-06 broken case extractor. One gold dot front sight. Three new flints for flintlock rifle. One #11 percussion cap nipple-5/16″-20 thd. Nipple wrench. One detachable sling swivel. One complete Anschutz complete front sight & one missing parts. One Anschutz rear sight disk. One Lyman Tong Tool 429 cast bullet sizer with 7/8″-14 bushing. One Weaver 63B scope mount for Marlin 336 and other rifles. New, unused with mounting screws. One reloading die wrench of unknown make.
M1 Garand Parts
Price: $20.00
Parts to keep your Garand shooting. Includes a hammer, trigger assembly, various pins, firing pins, extractors, rear sight slide, springs, and chamber brushes.
1911 Pistol Parts
Price: $15.00
Various pins and springs for the 1911 and 1911A1 handguns.
Bench Top Priming Tool
Price: $45.00
Lachmiller benchtop priming press. This tool should be considered an antique and worth lots. It is one I’ve used since I was in High School. That’s a long time ago. It works fine and is in good condition other than some minor dings to the paint. Comes with a small and large primer seating punches for both flat and rounded primers. There is an adjustable stop to control the seating depth. Also has a RCBS style shellholder of unknown make for 308 Win. and similar cases.
Redding Powder Measure
Price: $40.00
Redding powder measure with Herter’s stand. Used and in good condition. Standard metering chamber. The plastic powder tube (hopper) has been glued to the measuring body as it kept falling off.
RCBS Rockchucker Press
Price: $175.00
RCBS Rockchucker press. Used. Very good condition with little wear. Some minor chips to paint. This press is roughly forty years old but still ready to use. The shellholder retainer clip on the ram is missing but that never bothered me when I used the press. Probably could get one from RCBS. It has the priming arm which I never used and the slot in the top of the press for the primer feed attachment. That was optional and I never got it as I used a Lachmiller bench mounted priming tool. The primer catcher tray is on the press. It is no longer needed as I use the WH-2 press for reloading.
Bonanza Co-Ax Press
Price: $135.00
Forster Co-Ax press. Originally the Bonanza Co-Ax but for some time has been Forster. Either way it is about the best press for reloading there is. Not especially good for bullet swaging even with reloading press swages. But for reloading ammo it is hard to beat. This press has the standard jaws and is set to reload 308 Winchester or similar cartridges. Turn the jaws around to reload 223 Remington/5.56 NATO cartridges. It uses a standard RCBS style shellholder in the top of the press to prime cases. Comes with two primer punches and two extra springs for the shellholder plates. Spent primers drop down through the press ram and into a collection container under the press. The drop tube and container are not in the photo but are with the press. The press is used and in good condition.